Virginia Beach Project Update

After letting the last coat of epoxy on the hull dry for several days I did minimal touch up sanding of high spots. As I look back I should have done a lot more from an appearance standpoint but it certainly has a passable appearance. I again wiped the hull down well after having vacuumed the garage so that I was in as dust free as possible. I then used masking tape around the gunwale line feeling that the glue would probably adhere better to the epoxy directly than to a coat of paint. I used Rustoleum Marine primer, one coat applying it with a foam roller. It was difficult paint to stir and get well mixed but it went on very well and the roller gave it a good smooth even appearance. I again let it dry well for a couple of days and then used Rusteolem Marine Topsides paint for a finish coat. It too was rolled on and was easy to use. It will take a second coat to achieve a really nice look. It should be noted that this is Topsides paint not designed as “bottom” paint so if you plan on leaving a boat in the water for any long periods of time this is not the paint to use.

One final comment on the paint. Compared to the usual marine paints Rustoleum is much cheaper but also offers a more limited choice of colors and it would appear that it is not designed to be used as a mixing base to make your own color.

I let her get good and dry and then flipped her over onto a nice soft cloth pad to protect the paint. The frames were still attached and were the way I supported the boat while painting. Now for the first time I got a good look at the inside of the boat. WOW! I had a lot of finishing to do. This included filling screw holes but mainly if was filling in and making filets were the chines, keelson etc. did not seal as tightly as I would have liked. From a functional standpoint the boat was sealed. From and esthetic one I had a lot of work ahead of me. Since the epoxy is pricey I mixed up just enough so I knew that there would be no waste. This was your peanut butter consistency and applied with a tongue depressor went on easily and gave a nice effect. I would give a piece of advice when doing this. Wipe off the excess with a vinegar soaked cloth as soon as you are finished with an area. It is a heck of a lot easier than sanding this rock hard stuff once it dries. 

I still had the frame “legs” uncut. The center ones in particular were a real nuisance to work around so I cut them off almost to where they will be finally but since I still have work to do on the sheer as far as trimming off the plywood I left a few inches that will come off later. Now I at least wasn’t catching myself on this stick that was serving no purpose. The bow and stern legs weren’t nearly the problem and I still haven’t touched them. I went off the CABBS plans for the mast step and thwart. I saw in someone’s plans that they had enclosed this part and made a buoyancy box out of it. I used ¼” maranti for the top which I fitted up tight to the underside of the inwales. Put a few cleats along the sides and fore piece to hold it tight. I then scribed a pattern on cheap plywood for the vertical piece. For this I used ½” maranti figuring that this would be extra cross bracing since I am using ½” plywood instead of the ¾” per plans. I will cut a 2 3/8” hole at the point 11” back from the bow and into this will go a piece of 2” PVC. When finished it will be sealed with epoxy.

What I haven’t got straight (so to speak) yet is the rake of the mast and exactly how the step will be angled. The mast will be reinforced 1 ½” PVC. From what I can tell, and Kyle Leonard has said, the mast should be perpendicular to the sheer line That is what I finally did. I took a piece of 1x4 sprude, used a 2 3/8’ hole saw an cut completely though it and attached it to the keelson in just the right position so that the 2” pPVC would be perpendicular to the sheer line. Not as difficult as it may sound. Used epoxy to fasten it. I put in a 4” water tight inspection port in the vertical piece a little off center so that the area may be used to store a towel etc. I will have pictures of all this. The port cover is frm West Marine and cost less than $10. Really happy with it. As looked at the inside of the bow transom it just looked unfinished so I took a piece of 1x4 spruce, as clear as I could find, and scribed a piece to fit on the inside of the bow on top of the mast thwart. I think it looks pretty good. I am doing the same on the stern with the exception that there will be a perpendicular piece running down to the keelson. Since the gugeons will attach here the added strength makes sense. BUT all this trim work adds weight to the boat so for those wanting the lightest craft possible all this is not for you.

Read More..

Dinghy Cruising Around the Eye of Quebec

This is a good video if you can block out the time - 40 minutes. A duo spend two weeks going around a natural circular body of water in central Quebec, formed by the impact of an asteroid.

From the blurb accompanying the video:

"The Eye of Quebec (Lac Manicouagan) is visible from space as a perfectly ring-shaped lake. Its center island is far larger than the water that surrounds it. 100km in diameter, it is the fourth largest meteor impact site on earth. We sailed around it and think that was the first ever circumnavigation of the reservoir under sail and oar. (We can find record of two other sailboats that have attempted the trip. While were not sure of their success, both appeared to carry auxiliary engines. If it wasnt the wind pulling us it was our backs.)

Three years ago, when John and I drove the Trans-Labrador highway, we camped one night on the shores of the great Manicouaga and it captured our imaginations. Finally, this year, aboard the expedition re-fitted Wayfarer 4610, we made the voyage. We were on the water for about twelve days after a two day drive north. It is an astronomically great lake.

We camped ashore every night, and packed nearly 100 Ibs of dried food for the journey. We wore drysuits most of the time, cause the weather was typically cold and wet!

Circumanic Higher Res from Scott McDougall on Vimeo.

More information on the "Eye of Quebec" from Wikipedia.

Read More..

HYC Cruise Day 4 Tuesday July 28 Mattituck to Noank 35 Miles

Views exiting Mattituck

     

Yesterday I described Mattituck Creek as "scenic," so I added a few views taken on our way out. Tide was "up" so no depth problems today

North Star left first, headed for Block Island where we will join them tomorrow. ILENE left next and took this picture of Blast as she passed us.

The wind was from behind, but rather light. It provided only a few tenths of a knot to our engine speed. The biggest help was the tide rushing out of the Sound as we passed alongside its end, pulling us along. ILENE got about three knots at one point, making 8.5.

The posts from this cruise are being sent back to the Club and posted on its own blog. The Fleet Captain, moi, made a stupid mistake but fortunately a harmless one. ILENE and Blast had made reservations at Spicers. However, in my mind, I was thinking of the Noank Boatyard, where the Club Cruise stopped in Noank in 2012. I remembered where the Noank Boatyard was and went there, despite PC Bruce advising last night that Spicers was a long walk to Abbotts lobster restaurant, where we had planned to have dinner. Bruce was right; he usually is. So arriving off the Noank Boatyard I found out that I did not actually know exactly where Spicers was. We had to go out again into Fishers Island Sound, go back east a bit and then North again to Spicers. The detour was only about 1.2 miles. In this picture the pencil points to Noank Boatyard, the pen to Spicers.

We asked to be berthed near Blast and they honored this request after a fashion as this photo from ILENE shows. A short swim away!

And yes it is a long walk to Abbots so we dined at The Sea Horse, located in Spicers, the six of us from ILENE and Blast. Food pretty good. It was another quiet night. A bit of wind would have cooled things off. It is always cooler on the water but snuggled into slips it was hot.

Read More..